How to Install Wallpaper

The wallpaper is a decorative material for the walls which is quite easy to install yourself, just how to proceed. Before the installation of wallpaper, you must make a plan to facilitate the work.
The majority of wallpapers are pre-pasted and vinyl. Simply use a tray to soak the wallpaper roll upholstery and activate the adhesive on the back of it.
Walls should be clean and smooth. So you need to repair the holes and clean the wall surface. Remove switch plates and electrical outlets, by putting the screws on them to avoid losing them.
The renovations are often more difficult because it is common for walls, doors, and others have changed over time. Moreover, as it is possible that a wall is inclined, like a cathedral ceiling, for example, you must draw a line starting at the well. It is also important to minimize the cuts strips of tapestry, which is more work, and can produce more material loss.
The party has the most open or cutting is often one where you should start by calculating the laying tape the widest possible. For example, if the section between a window and a door 22 inches and the band are 18, it may be best to start half way and have two strips of 11 inches. The C-shaped band of 11 inches is less sensitive than that would have only 4.
Once you have decided where to begin, draw a straight line with a level. This line of departure when the tapestry does not make sense for the installation. If it must always be stuck in the same direction, measure the number of bands complete before starting the corner. Then, transfer your starting line to mark the start of the first full edge. You get the bandwidth you need to start cutting.
To cut the wallpaper, you need a sharp knife and scissors. Easy to cut the edge of a door frame, you smooth the wallpaper into the corner. Then, with a metal spatula, you press in the corner to hold the wallpaper in place while you trim the excess along the spatula with your knife. Once the cut side, you use the scissors to cut the wallpaper about midway of the molding at the top of the door. This allows you to place, smooth and cut above the door as if to the side.
Once a strip of wallpaper is stuck, straighten it well to release air bubbles and excess glue. Remove as much glue on the surface; it’s easier than when dry.
You must install the wallpaper straight, because the motive is often to highlight the defects. It is always best to ask two of the tapestry, which lays the strips more quickly and accurately. Just to properly calculate the starting position, to take time off for good equipment, and smooth to remove bubbles. It is a work of decoration that requires a little more DIY scamper, but not really difficult. Good luck.

How to Remove Wallpaper on a Wall

You have wallpaper that is broken, chipped or whether this is due to the influence of moisture, how do I remove it? Or do you want to replace your old wallpaper?  The wallpaper or wall covering that is glued to a wall with an adhesive. To remove the wallpaper, it is necessary to moisten the adhesive on the back of it to make it soft and ability to remove strips of wall covering without damaging the surface underneath.

The glue used to fix the tapestry is usually easy to dissolve, but the surface is sometimes plastic or waterproof. If the solution for stripping can not reach the glue, you must remove the impervious surface and remove the fiber and the adhesive remains on the wall.

If the impervious surface cannot be easily removed, then remove the glue, you should use a tool to break the surface of plastic wallpaper. This is roulette as a stapes riding as you drive on the wall to break through the surface of the coating and let the cleaner penetrate.

Before applying the stripping solution on the tapestry, use plastic sheeting with tape stuck on top of the baseboard. This will protect the wood paneling and decorative prevent wetting the floor. You do not want the cleaner can damage the paint baseboards or flooring.

You apply the thinner glue for wallpaper with a sponge or a paint roller, as directed by the product used. Once the solution has softened glue, using a spatula or knife plate to the cast. The ideal is to take off the wallpaper from top to bottom of the wall, to use gravity and help you in this work.
It is possible to drill a few inches up the wall, once part of the membrane peeled off, you sprinkle a little cleaner on the wall that runs between the coating and wall and reach the adhesive. This allows for less surface damage by piercing the wallpaper and less repair of the wall.

Once the siding removed, clean and prepare the surface properly and the wall several times, to ensure that it remains a film of glue on it. You often make minor repairs with plaster. Depending on the condition of the surface, a paint primer is usually necessary to ensure a uniform decorative painting.

Allow to dry properly once the wall washing done. Putting paint on gypsum wet does not work well, and humidity will be trapped behind the paint, which can produce swelling and air pockets caused by the drywall paper from taking off. That’s a lot of work to remove a wall covering and upholstery is therefore better to do the job properly Happy to change your wallpaper. I hope this tip useful. I am waiting for your input for further troubleshooting